- Home
- 1A1 Resin Bond Diamond Wheel|1A1 Straight Diamond Grinding Wheels
Catalogue
Catalogue
Superabrasivetools company’s 1A1 resin bond diamond wheels are manufactured using high-quality diamond abrasives and premium resin bond, produced through a hot-press sintering process. These 1A1 resin bond diamond wheels are widely used for flute grinding, surface grinding, OD grinding, knife grinding, profile grinding, and centerless grinding, providing highly efficient grinding performance.

Among all bond types of superabrasive wheels, 1A1 resin bond diamond wheels offer the widest diameter range. They are also the most widely used type, accounting for more than 50% of total grinding wheel sales in many applications.
The 1A1 resin bond diamond wheel is designed for precision grinding of hard and brittle materials such as tungsten carbide, PCD/PDC tools, ceramics, sapphire, optical glass, and semiconductor materials. With its resilient resin bond, excellent toughness, and effective heat and vibration reduction, it performs reliably in rough grinding, semi-finishing, and finishing/edge grinding stages.

This type of wheel can efficiently remove excess material while minimizing grinding stress and thermal damage to the workpiece, helping to prevent edge chipping and micro-cracks. Typical grinding operations include OD grinding, ID grinding, tool sharpening, and surface grinding.
It is widely used in cutting tool manufacturing, optical and semiconductor processing, precision ceramic component machining, and finishing of high-hardness molds, delivering high dimensional accuracy, low surface roughness, and extended service life for both the grinding wheel and the workpiece.
If you need to choose a 1A1 wheel with a hybrid bond, you can refer to the case study:Select Best Hybrid Fluting 1A1 grinding wheel|Diamond|CBN 2025
Tungsten Carbide Wooden Keyhole Cutter Grinding By 1A1 Hybrid Wheels Case Study:2025 Test a Diamond 1A1 Fluting Wheel For Wooden Keyhole Cutter
Grinding Mechanism of Resin Bond Diamond Wheels
1A1 resin bond diamond wheel combine elasticity and self-sharpening characteristics. Due to their relatively soft structure, dull abrasive grains can easily detach during grinding, continuously exposing new sharp grains and allowing the grinding wheel to maintain consistent cutting performance.
At the same time, the high elasticity and good vibration-absorbing properties of the resin bond help reduce grinding impact and vibration, thereby improving the surface quality of the workpiece. In addition, resin bonds provide effective heat dissipation, allowing grinding heat to disperse quickly and reducing the risk of workpiece burn and micro-cracks.
These advantages make resin bond diamond wheels particularly suitable for precision and mirror-finish grinding of optical glass, ceramics, PCD tools, and other hard and brittle materials.
2.Parameter information of 1A1 resin bond diamond wheel

Common Diameter Range for 1A1 Resin Bond Diamond Wheels
| D × T × H × X (mm) | Typical Applications |
|---|---|
| 50 × 6 × 20 × 3–5 | Small tool grinders, laboratory equipment |
| 75 × 10 × 25 × 5 | Micro tools and precision component grinding |
| 100 × 10 × 20 × 5–8 | Tungsten carbide tools, PCD tool grinding |
| 125 × 12 × 31.75 × 6–10 | Standard size for tool grinding machines |
| 150 × 15 × 31.75 × 8–10 | Tool sharpening and precision parts |
| 200 × 20 × 31.75 × 10–12 | Surface grinding and ceramic components |
| 250 × 25 × 50.8 × 10–15 | Mold processing and hard material grinding |
| 300 × 30 × 76.2 × 12–15 | Large surface grinding machines |
| 350 × 35 × 76.2 × 15–20 | High-efficiency grinding |
| 400 × 40 × 127 × 15–20 | Heavy-duty industrial grinding |
Larger diameters are also available, such as 600 mm, 700 mm, or even 900 mm, which are typically used for thermal spray coating grinding applications. These are custom-made products, and customers are welcome to contact us for further details and customization options.You can reach us at info@superabrasivetools.com, and our engineers will get back to you as quickly as possible—typically within 24 hours.
Advantages of 1A1 Resin Bond Diamond Grinding Wheels
Resin bond is the most widely used bonding system for diamond grinding wheels, with more than 50% of superabrasive wheels utilizing resin bonds.
Resin bond diamond grinding wheels combine elasticity, self-sharpening capability, and low-temperature grinding characteristics, offering significant advantages over metal bond diamnd wheel and vitrified bonds diamond wheel:
- Better self-sharpening and less loading:Resin bonds are softer than metal or vitrified bonds. When abrasive grains become dull, they can detach naturally, exposing new sharp cutting edges. This allows the grinding wheel to remain sharp, preventing chip loading and reducing the risk of burning the workpiece.
- Elastic vibration absorption for higher surface quality:The inherent elasticity of the resin bond acts as a buffer, reducing grinding vibration and impact. This helps achieve smoother surfaces without chipping or scratches, making it ideal for optical glass, ceramics, PCD tools, and mirror-finish grinding applications.
- Lower grinding temperature to protect the workpiece:1A1 Resin bond diamond wheels provide efficient heat dissipation and a gentler grinding action, which helps minimize workpiece burn, micro-cracks, and thermal deformation. They are particularly suitable for heat-sensitive and high-precision materials.
- Easy forming, simple dressing, and strong versatility:Compared with the dense structures of vitrified or metal bonds, resin bond diamond wheels are easier to dress and maintain. They also offer broader application flexibility and generally lower overall operating costs.
FAQ(1A1 Resin Bond Diamond Wheel)
4.1 Detailed comparison of resin binders (dry grinding and wet grinding)
4.1.1 Dry grinding of 1A1 Resin Bond Diamond Wheel
Dry grinding conditions: Polyimide-based resin bonds should be used. If the grinding load is extremely heavy or if exceptionally long wheel life is required, ultra heat-resistant polyimide resins specifically designed for heavy dry grinding can be selected. In some cases, polyimide formulations containing metal powders (such as copper powder) are used to further enhance heat resistance and thermal conductivity.

Wet grinding of 1A1 Resin Bond Diamond Wheel
Wet grinding conditions: Phenolic resin is generally the preferred choice due to its excellent cost-performance ratio. If higher heat is generated during wet grinding, or if a longer service life is required for the 1A1 resin bond diamond grinding wheel, heat-resistant modified phenolic resins or polyimide resins can also be considered to achieve better overall performance.
If you can provide specific grinding parameters—such as grinding depth, feed rate, and workpiece material hardness—we can recommend a more precise resin grade or formulation direction tailored to your application.
Comparison table of phenolic resin binders for dry grinding and wet grinding
| Item | Dry Grinding Phenolic Resin Bond | Wet Grinding Phenolic Resin Bond |
|---|---|---|
| Resin Type | Modified phenolic resin / High heat-resistant phenolic resin | General phenolic resin / Toughened modified phenolic resin |
| Heat Resistance | High (180–250°C) | Medium (120–180°C) |
| Bond Hardness | Relatively high | Medium or relatively soft |
| Grit Retention | Strong | Medium |
| Self-Sharpening | Low | Good |
| Filler Type | Metal powder, heat-resistant fillers | Graphite, lubricating fillers |
| Thermal Conductivity | Relatively high | Medium |
| Anti-Clogging | Medium | Strong |
| Grinding Temperature | Relatively high | Relatively low |
| Grinding Force | Relatively large | Relatively small |
| Surface Roughness | Average | Good |
| Wheel Life | Medium | Long |
| Cooling Method | No cooling or slight air cooling | Water-based or oil-based coolant |
| Typical Applications | Stone, rough grinding of glass, building materials | Cemented carbide, PCD tools, ceramics, optical materials |
How to select the grit size of 1A1 resin bond diamond wheels
Core selection criterion: Divided by processing stage, this is the most common selection logic, usually divided into three stages: rough grinding, semi-fine grinding, and fine grinding
| Processing Stage | Recommended Grit (Mesh) | Main Objectives | Typical Applications |
|---|---|---|---|
| Rough Grinding | 60# – 120# | High-efficiency stock removal, shaping | • Rough grinding of blanks • Rapid thinning of thick thermal spray coatings (>0.5mm) • Slotting of cemented carbide |
| Semi-Finish Grinding | 150# – 325# | Balance efficiency and quality, prepare for finish grinding | • Remove rough grinding lines • Dimension close to final requirement (0.02–0.05mm stock left) • Cutting edge preparation for carbide tools |
| Finish Grinding | 400# – 800# | Achieve final dimensional accuracy and surface roughness | • Carbide seal rings, mold surfaces • Surfaces requiring Ra 0.2–0.4 μm |
| Super-Finish / Mirror Grinding | 1000# – 3000# | Obtain mirror finish and extremely low damage layer | • Precision optical molds • Silicon wafer cutting • Super-hard coatings requiring Ra < 0.1 μm |

Consider Stock Allowance:If the stock allowance is >0.1 mm, choose a coarse grit (#80–#180).If the stock allowance is <0.03 mm, proceed directly to fine grit (#400 and above).
Consider Surface Roughness:For surface roughness Ra ≤ 0.4 μm, use at least #400 grit.For Ra ≤ 0.2 μm, select #600 grit or finer.
Consider Burn Risk:For heat-sensitive materials (e.g., tungsten carbide, ceramics), to minimize the risk of burning while meeting surface roughness requirements, it is recommended to choose a slightly coarser grit to facilitate cooling.
These are reference guidelines. In actual selection of 1A1 resin bond diamond wheels, many other factors—such as grinding parameters, wheel bond type, and workpiece material—must also be taken into account.
How to dressing a 1A1 resin bond diamond wheels

How to Storage and Handling of 1A1 Resin Bond Diamond Wheels:
1A1 resin bond diamond wheels should be stored in a dry, cool, and well-ventilated environment, protected from moisture, direct sunlight, and high temperatures to prevent resin aging or embrittlement. Wheels should be placed flat or vertically, and heavy stacking, collisions, or compression must be avoided.
Before use, inspect the wheel for cracks, chipping, moisture absorption, or softening. New wheels should be run at low speed for a short period and properly dressed to ensure dynamic balance. During grinding, ensure adequate cooling to reduce thermal damage to the resin.

After use, clean off surface debris promptly. Handle carefully during transport and loading/unloading, avoiding dropping, striking, or bumping the wheels. Proper storage, handling, and operation practices extend wheel life and ensure safe use.
Case studies of grinding 1a1 resin bond diamond wheels
Case Study of Thermal Spraying with 1a1 Resin Bond Diamond Wheel Grinding
Parameter Table for Thermal Spray Coating Process of 1A1 Resin Diamond Grinding Wheel
| Parameter Category | Specific Parameter Name | Rough Grinding (High Removal) | Semi-Finish Grinding (Transition) | Finish Grinding (Final/Smoothing) | Unit | Remarks/Notes |
|---|---|---|---|---|---|---|
| Wheel Specification | Wheel Type | 1A1 | 1A1 | 1A1 | - | Parallel disc or straight rim |
| Abrasive Type | Synthetic Diamond (RVD or MBD) | Synthetic Diamond (MBD or SMD) | Synthetic Diamond (SMD or CVD) | - | Resin bond suitable for sharpness requirements | |
| Grit Size | 80# - 120# | 200# - 325# | 400# - 600# | Mesh | Coarser grit = higher removal rate; finer grit = better surface finish | |
| Concentration | 100% | 100% | 75% - 100% | % | 100% concentration ≈ 4.4 ct/cm³ | |
| Recommended Diameter | 200 - 400 | 200 - 400 | 200 - 400 | mm | Common: 200–300 mm for surface grinding, 300–400 mm for cylindrical grinding. Determined by machine spindle interface. | |
| Grinding Parameters | Wheel Speed (Vs) | 25 - 30 | 28 - 32 | 30 - 35 | m/s | Avoid excessively high speeds for resin wheels to prevent burning. |
| Table Speed (Vw) | 15 - 20 | 12 - 18 | 8 - 12 | m/min | For reciprocating surface grinding | |
| Depth of Cut (ap) | 0.02 - 0.05 | 0.01 - 0.02 | 0.002 - 0.005 | mm | Infeed per pass or per stroke | |
| Cross Feed (Step-over) | 2 - 4 | 1 - 2 | 0.5 - 1 | mm/st | Coefficient of wheel width utilization | |
| Cooling Conditions | Coolant Type | Water-based emulsion or diamond grinding fluid (low concentration) | Same as left | Same as left | - | Adequate cooling is essential to prevent resin softening. |
| Flow Rate | > 20 | > 25 | > 30 | L/min | Adjust based on grinding zone width. | |
| Typical Results | Material Removal Rate | High (5 - 15 mm³/s) | Medium (2 - 5 mm³/s) | Low (< 1 mm³/s) | - | Estimated values |
| Surface Roughness (Ra) | 1.2 - 0.8 | 0.6 - 0.4 | 0.2 - 0.1 | μm | Can achieve mirror-like finish for WC-Co coatings. | |
| Grinding Ratio (G-ratio) | 80 - 120 | 100 - 150 | 120 - 200 | - | Resin wheels typically have a high G-ratio when grinding thermal spray coatings. | |
| Surface Condition | Visible grinding marks | Fine pattern | No burns, no cracks, bright finish | - | Thermal spray coatings are prone to cracking; caution required. |
Wheel Selection Guidelines for Thermal Spray Coatings
Why choose resin bond?
1A1 Resin bond diamond wheels offer excellent self-sharpening and high elasticity, providing superior polishing and surface finish. They are particularly suitable for grinding heat-sensitive or crack-prone thermal spray coatings, such as ceramic coatings.
Grit Selection:
For WC-Co (tungsten carbide type) coatings, it is recommended to use #500–#800 grit for finishing.
For alumina (Al₂O₃) or chromium oxide (Cr₂O₃) ceramic coatings, #400–#600 grit usually achieves optimal surface quality.
Cooling Considerations:
Thermal spray coatings generally have poor thermal conductivity, especially ceramic layers, causing heat to accumulate during grinding. Resin bond wheels soften and lose abrasive grains under high heat, while the workpiece is prone to burning. Ensure that the coolant is directed precisely at the grinding arc zone to maintain wheel and workpiece integrity.
Dressing Recommendations:
Resin diamond wheels require regular dressing to maintain sharpness. Typically, green silicon carbide (GC) stones or soft steel tools are used for manual or in-line dressing, exposing fresh diamond grains and removing resin residue.
Operational Data & Adjustments:
For OD grinding, slightly reduce the workpiece speed while allowing the wheel line speed to increase up to ~35 m/s.If vibration marks appear during grinding, check wheel balance or reduce the wheel line speed as necessary.
Diameter of 1a1 resin bond diamond wheel (grinding thermal spraying)
| Shape Code | Diameter (D) | Hole (H) | Thickness (T) | Abrasive Width (W) |
|---|---|---|---|---|
| 1A1 | 100 mm | 20 mm / 25.4 mm | 10 mm / 12 mm | 6 mm / 10 mm |
| 1A1 | 200 mm | 76.2 mm | 25 mm | 10 mm |
| 1A1 / 14A1 | 300 mm | 76.2 mm | 25 mm | 10 mm |
| 1A1 | 300 mm | 127 mm | 25 / 30 / 40 / 50 mm | 6 / 10 / 25 mm |
| 1A1 | 400 mm | 127 mm | 25 / 30 / 40 / 50 mm | 10 mm |
| 1A1 | 500 mm | 203 / 254 mm | 15 / 25 mm | 10 mm |
| 1A1 | 600 mm | 203 / 254 / 304.8 mm | 25 / 40 / 50 mm | 5 / 10 / 25 mm |
| 1A1 / 14A1 | 700 mm | 304.8 mm | 40 mm | 10 mm |
| 1A1 | 900 mm | 304.8 / 305 mm | 50 mm | 10 mm |
| 1A1 / 14A1 | 1100 mm | 304.8 mm | 50 mm | 10 mm |
Case Data on Grinding Carbide with Small Diameter 45mm 1A1 Resin Diamond Wheel
| Parameter Category | Specific Parameter | Case Data / Recommended Value | Unit |
|---|---|---|---|
| Wheel Specification | Wheel Type | 1A1 resin bond diamond wheels | - |
| Wheel Outer Diameter | 45 | mm | |
| Wheel Thickness / Height | 5 | mm | |
| Bore Diameter | 9.5 | mm | |
| Bond Type | Resin | - | |
| Abrasive Type | Diamond (SDC) | - | |
| Grit Size | Rough: 150#; Finish: 400#; Also 230# case | Mesh | |
| Concentration | 100% | % | |
| Grinding Parameters | Wheel Speed (Vs) | 20 - 22 | m/s |
| Workpiece Feed Speed (Vw) | 40 - 50 | mm/min | |
| Depth of Cut (ap) | Rough: Details unknown; Finish: 0.002 - 0.005; Also 1.4 - 1.6mm deep cut case | mm | |
| Cooling Conditions | Coolant Type | Water-based grinding fluid (Wet grinding) | - |
| Grinding Results | Grinding Force (Fn) | 28 - 110 | N |
| Grinding Temperature | 32 - 200 | °C | |
| Surface Roughness (Sa) | 0.31 - 0.76 | μm | |
| Surface Condition | Grinding burn may occur if parameters are improperly selected | - |
Diameter and Spindle Speed Matching:For small-diameter wheels (e.g., 45 mm), achieving a line speed of 20–35 m/s requires a high spindle speed. For example, a 45 mm wheel needs approximately 12,700 rpm to reach 30 m/s line speed. Ensure that your grinding machine supports the required spindle speed range.
Dressing Tools:Small 1A1 resin bond diamond wheels can be dressed using molybdenum rods, dressing strips, or copper sticks to maintain sharpness.
Importance of Cooling:Grinding tungsten carbide or similar hard materials generates significant heat. Adequate cooling is essential to prevent resin bond softening and workpiece burn, ensuring both wheel performance and workpiece quality.
Why choose SUPERABRASIVETOOLS company 1A1 resin bond diamond wheel?
Choosing SUPERABRASIVETOOLS company’s 1A1 Resin Bond Diamond Wheel represents a commitment to precision grinding quality, reliable durability, and excellent cost-performance. Leveraging SUPERABRASIVETOOLS company’s core superhard material technology, this wheel is manufactured under strict quality control and offers outstanding performance, making it an ideal solution for grinding hard-to-machine materials such as tungsten carbide, ceramics, and PCD/PCBN tools.
6.1 Core Manufacturing Processes (The Foundation of Quality)
- Premium Diamond Abrasives: High-quality synthetic diamonds with complete crystal structure and high purity are selected, with precisely graded particle sizes to ensure consistent sharpness and uniform grinding performance, guaranteeing machining accuracy from the source.
- High-Precision Resin Bond Formulation and Sintering: Resin bonds are used and hot-pressed under precise temperature and pressure, providing strong abrasive retention, minimal grain loss, and no cracking. The wheel’s overall rigidity and heat resistance are significantly enhanced.
1A1 Parallel Structure with Precision Forming: The parallel end face is machined to high precision, with strict control of concentricity, flatness, and radial runout, making it suitable for surface grinding, OD grinding, and tool edge grinding in high-precision applications.
- Full-Process Quality Control and Dynamic Balancing: From raw material blending, pressing, sintering, to dressing and inspection, the entire process is standardized. Finished wheels undergo precision dynamic balancing, ensuring stable, vibration-free operation at high speeds.

1A1 Resin Bond Diamond Wheel Core Advantages (Performance Value)
- High Grinding Accuracy and Excellent Surface Finish: The parallel working surface distributes force evenly, achieving a stable surface roughness of Ra ≤ 0.1 μm. Workpieces remain free from burn marks and edge chipping, reducing the need for subsequent polishing.
- Wear-Resistant and Long-Lasting: The combination of high-hardness diamond abrasives and strong resin bond retention results in minimal wear, with a service life 5–10 times longer than conventional wheels, significantly reducing wheel replacement and production costs.
- Excellent Self-Sharpening and High Cutting Efficiency: During grinding, worn abrasive grains naturally detach, continuously exposing fresh cutting edges, maintaining long-term sharpness. This ensures high efficiency, minimal loading, and rapid heat dissipation.
- Wide Compatibility and Stable Operation: Compatible with various universal grinding machines and CNC tool grinders, suitable for grinding tungsten carbide tools (内链), ceramic components, magnetic materials, and PCD/PCBN tools. The wheel maintains consistent geometric accuracy over long-term use.

SUPERABRASIVETOOLS company Type 1A1 Resin bond Diamond Wheels are exported to the United States, South Korea, Malaysia, Germany, France, Mexico, Vietnam, Italy and other countries. We offer products with reliable quality at competitive prices, providing customers with stable and dependable grinding solutions.
We also attach great importance to after-sales service, actively listen to customer feedback, and continuously improve the quality of our diamond grinding wheels and after-sales service through effective communication.If you need to order 1A1 diamond grinding wheels, please feel free to contact us for a quotation.
Related Reading: Why can resin diamond grinding wheels achieve Ra0.05 with a 1200# grit, while vitrified bond diamond wheel cannot?
Customer’s question:When I use a resin-bonded 1200# grinding wheel, I can achieve Ra 0.04–0.05. But after switching to a vitrified bonded diamond grinding wheel, I can only reach Ra 0.1. Why is that?
Answer:This customer processes ceramic components such as zirconia, alumina and silicon carbide, using an internal grinding diamond wheel with a diameter of 18 mm. The issue is mainly related to the different grinding characteristics of resin-bonded and vitrified-bonded wheels, as well as the relationship between abrasive grit size and surface roughness.
9.1 Ceramic Bond vs. Resin Bond
Resin-bonded abrasive tools feature excellent self-sharpening, low clogging, good elasticity, and superior polishing performance. However, they have relatively low bond strength, resulting in weaker diamond retention, heat resistance, and wear resistance.
Resin bond diamond wheel exhibits a typical grain embedding phenomenon. This is especially obvious with micro-powder grade grinding wheels. Insufficient grinding fluid supply at the cutting zone leads to heat conduction into the bond, softening the resin and intensifying grain embedding. Reduced grain protrusion helps achieve better surface roughness; however, excessive embedding lowers grinding efficiency, and may even cause direct contact between the bond and the workpiece, further increasing temperature, softening the bond, and resulting in abnormal grain loss. In such cases, timely wheel dressing is required to avoid quality issues.
For applications where grain embedding is undesirable, the rigidity of the bond can be improved through formula adjustments. A common method in the industry is adding copper powder.
In contrast, vitrified bonded diamond wheels are completely different. They are characterized by high porosity and high rigidity, with much stronger grain retention than resin bonds. Naturally, the ground surface roughness will be higher (coarser) at the same grit size.
9.2 Relationship between Different Binders, Abrasive Grain Size, and Roughness
After understanding the characteristics of different bond types, it is easy to understand why the same grit size can produce different surface roughness when using resin-bonded and vitrified-bonded wheels.
Now that the customer has been using resin-bonded diamond grinding wheels and wants to switch to vitrified-bonded diamond wheels, how should they adjust the grit size? They can refer to the chart below.

It can also be seen from the chart that to achieve the same surface roughness, vitrified bonded grinding wheels require a finer grit size. Generally, it is necessary to go 1–2 grit sizes finer.
Another frequently asked question:
For fine grinding and ultra-precision grinding, should we choose resin-bonded diamond wheels or vitrified-bonded diamond wheels?
Actually, there is no absolute, universal answer—it all depends on your priorities.
Resin-bonded diamond wheels offer the advantages of excellent surface roughness and strong polishing performance, making it easier to achieve high-quality finishes. However, their retention of form and position accuracy is not as good as vitrified wheels, and their service life is relatively shorter, while they are more cost-effective.
In contrast, vitrified-bonded diamond wheels have obvious advantages in form and position accuracy, wear resistance and service life, with greater stability, but at a higher price.
In short:If you do not have high requirements for service life and prioritize finish and cost, resin-bonded diamond wheels are an ideal choice.If you have high demands for machining accuracy, surface finish and service life, and are less sensitive to price, vitrified-bonded diamond wheels are the better option.
At New Diamond Tools, we focus on quality customer service.
- Xinxiang New Zuan Diamond Tools Co., Ltd.
- 18# Building, Jingu Oriental Piazza, No.1 Jinsui Road, Xinxiang, Henan 453000, China
- +86-373-7199720
- +86-15803991654
- info@superabrasivetools.com








